Tepte.com
135 times.
The F0E1 Error Code indicates that you are trying to run a "Clean Washer" cycle and the washer is detecting there are items still in the washer/dryer.
Remove load and restart the Clean Washer with affresh®cycle.
The F0E2 Error Code indicates that there are excessive suds detected inside the washer/dryer.
The washer/dryer is running a suds reduction routine in order to reduce the amount of suds. Allow the cycle to continue.
Use only HE (high efficiency) detergent in this washer/dryer.
The F0E3 error code indicates that the temperatures in the washer/dryer are too hot during the dry cycle. Verify that you are using the right cycle for the fabrics being laundered.
Try resetting the washer/dryer by unplugging it from the outletfor at least 1 minute and then plugging it back in. If unsuccessful, call for service.
An F0E4 Error Code indicates that the wash water temperature is too hot. The washer/dryer may be connectedincorrectly to the home water supply.
The washer/dryer must be connected tocold water. Verifythat the unit is connected to the coldwater supply only.
See installation instructions for further information on connecting to the water supply.
The F0E5 Error code indicates that an off balance load has been detected. This means that the load in the washer/dryer could be too large, or it could be unbalanced.
Avoid tightly packing the washer/dryer. Avoid washing singleitems. Balance a single itemsuch as a rug or jeans with a
few extra items.
Note that an unbalanced load may not reach the intended washer spin speed for the cycle you selected. This could increase dry times.
The F1E4 Error Code indicates there may be a problem with the main relay.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in. If unsuccessful, call for service.
The F3E1 Error Code indicates that there may be aproblem with the Water Pressure sensor. Verify that your water supply has the adequate amount of pressure going to the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in. You may need to run a drain only cycle if there is still water in the Washer/Dryer. If unsuccessful, call for service.
The F3E2 Error Code indicates that there may be an issue with the Temperature Control sensor.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F3E3Error Code indicates that there may be an issue with the Air Inlet function. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F3E4Error Code indicates that there may be an issue with the sensor detecting the detergent level in the Load & Go™ Dispenser.
A potential cause of this Error Code is a clog in the dispenser.Clean the Load & Go™ bulk detergent dispenser,or add detergent manually until dispenser is cleaned. If you have questions about how to clean yourLoad & Go™ bulk detergent dispenser, see the "Cleaning and Maintenance" section of this Troubleshooting Guide, or review your Use & Care Guide.
The F4E2Error Code indicates that there may be an issue with the dryer heater circuit. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F4E3Error Code indicates that there may be an issue with the dryer blower motor. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E1Error Code indicates that there may be an issue with the doorswitch/door lock. The door is unlockedduring a cycle when it should belocked.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E2Error Code indicates that there may be an issue with the doorlock.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E3Error Code indicates that there may be an issue with the doorlock.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E4Error Code indicates that the washer/dryer door has not been opened between cycles. Three consecutive cycles were runwithout the door being opened. Thewasher/dryer will generate an invalidkey beep when START is pressed.
Open and close the door. Check for obstructions around thedoor switch and latch.Verify functionality of door switch by opening and closing the door.
For best results, removing clothing promptly once cycle has completed.
The F6E1Error Code indicates that there may be a communication failure between the electronics in the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F6E2Error Code indicates that there may be a communication failure between the electronics in the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F8E1Error Code indicates that the washer/dryer is not detecting any water flow going to the washer/dryer. This can be caused by several reasons, including the following:
Make sure that the washer/dryer is connected to the homecold water supply, and that the home water supply valve is fully open (turned on). Verify that the inlet hose to the washer/dryer is notkinked. If problem persists, call for service.
The F8E3 Error Code indicates that there may be an internal overflow from the water inlet valve.
Verify thatthe drain hose and drain pump filter are not plugged. See Cleaning and Maintenance section above for more information.
If this does not resolve the issue, call for service.
The F9E1Error Code indicates that the washer/dryer is not draining in a timely manner, or at all.This could be due to the following:
Clean the drain pump filter and the bellows drain holes(see Cleaning and Maintenance symptom above).
Check the drain hose for obstructions and verify installation. The drain hose cannot be more than 4.5 inches into the stand pipe or laundry sink. It also must be routed at least 24 inches from the floor, and not over 96 inches. See the installation instructions for more details of installing the drain hose.
Ask me about:
The F-01 error code indicates a primary control board failure on this model of dryer. If the error cleared after unplugging it for 20-30, then the control board could have received a power surge or glitch through the electrical lines.
Yes, there is a reset procedure to fix this. The Whirlpool Cabrio washers need to be reset in a different method than many other types and brands of washers. Here is how you can RESET your Cabrio washer (all Whirlpool Cabrio models). Follow the directions below and your washer should reset and begin to work normally.
Pull down on the bottom panel and pull it away from the washer. Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door.
The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
How does a communication error between the motor control unit and the main control board contribute to the F28 error code on a Maytag front loader washer, and what methods can be used to resolve this issue?
Maytag front loader washer / F28 error: Communication issue Answers: 2 8
How does an electrical or communication problem between the main control board and the user interface board contribute to the F23 error code on a Maytag front loader washer, and what steps can be taken to address this issue?
Maytag front loader washer / Pressure switch or water level detection problem Answers: 1 3
How does an issue with the door lock mechanism or the door latch assembly contribute to the F22 error code on a Maytag front loader washer, and what measures can be taken to fix the problem?
Maytag front loader washer / F22: Door lock error Answers: 2 4
How does a drain or pump obstruction contribute to the F21 error code on a Maytag front loader washer, and what methods can be used to clear the blockage and restore proper drainage?
Maytag front loader washer / Long drain time or clogged drain filter Answers: 2 3
How does a water inlet problem, such as insufficient water flow or a clogged inlet valve filter, contribute to the F20 error code on a Maytag front loader washer, and what methods can be used to resolve these issues?
Maytag front loader washer / No water detected entering the washer Answers: 1 2
How does a communication failure between the main control board and the motor control unit lead to the F11 error code on a Maytag front loader washer, and what measures can be taken to address this issue?
Maytag front loader washer / 11: Communication error Answers: 2 3
How does a communication problem between the control board and the motor contribute to the F09 error code on a Maytag front loader washer, and what troubleshooting methods can be employed to fix it?
Maytag front loader washer / F09: Overflow condition Answers: 1 3
How does a drive motor tachometer error contribute to the F06 error code on a Maytag front loader washer, and what steps should be taken for diagnosis and rectification?
Maytag front loader washer / F06: Drive motor tachometer error Answers: 2 3
How does a drain problem or a clogged drain filter lead to the F02 error code on a Maytag front loader washer, and what steps can be taken to address this issue?
Maytag front loader washer / F02: Drain problem Answers: 1 2
Are there any specific troubleshooting techniques or diagnostic tests that can help identify the underlying causes of the F01 error code on a Maytag front loader washer, and what are the recommended solutions?
Maytag front loader washer / F01: Main control board issue Answers: 1 3
Could you provide me with a list of error codes from 0--n for Whirlpool 6th Sense ovens? How many error codes are there for Whirlpool 6th Sense ovens, and what are they?
Whirlpool / error codes from 0 to n Answers: 1 3
What could be causing the doors on my Splendide Ariston AW122 stackable washer and dryer to not unlock after the cycle completes and the light flashes to indicate that the door should unlock?
Splendide / Ariston AW122 Answers: 1 5
How do I get my GE Washing Machines drive shalf or shifter it to open?
GE / Washing Machines Answers: 2 3
What is causing a Frigidaire stackable washer/dryer to shake violently during the spin cycle?
Frigidaire / Washer Answers: 1 4
What should I be looking for to stop the gas smell coming from inside the oven when I turn it on?
Oven / gas smell Answers: 2 3
