Learn Asko Dishwasher Fault(Failure) Codes and Check Repair
Asko Dishwasher Error/Failure Code: F1, Error/Failure Code: F2, Error/Failure Code: F3, Error/Failure Code: F4 fault codes. if you have problems always check the owners manual first, it may well have the information you need and will be specific to your Appliance.
Subject: Asko Dishwasher - Sub Subject: Fault CodesDate: 6/30/2019 Status: SOLVED
6 answered / 23 voted,
807 viewed.
technician - Sunday, June 30, 2019 941Asko Dishwasher Fault Codes
Failure Code: F1
Condition: Water heating fault, selected temperature not reached within 60 minutes
Check/Repair:
Incoming water temperature too cool
Heating element burned out
Thermostat defective
Failure Code: F2
Condition: High water level
Check/Repair:
Plugged/Bad water pump
Defective water inlet valve
Failure Code: F3
Condition: Thermistor fault
Check/Repair:
Open thermistor
Bad wiring to thermistor
Failure Code: F4
Condition: Fault with water fill (only on machines with level-controlled fill)
Note: Lights blinking, pump running and controls dead indicates an over fill fault.
Check/Repair:
- Disconnect the power to the unit
- Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water)
- Use a towel or a sponge to remove the water
- There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional
- Test the dishwasher
- If there are no leaks from the dishwasher into the pan, check the drain hose under the sink
- The drain hose must run up to the top of the underside of the countertop then down to the drain. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray)
The best ReplyANSWERS Write an Answer
❝Learn Asko Dishwasher Fault(Failure) Codes and Check Repair❞ answers. technician asked first. Total 6 replies.
location: Broken Arrow, OK?
0
0 0 0 0 0 0 0Must visit San Diego, CA?
0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 513
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3638
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 638
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 516
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 351
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 395
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 325
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 536
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 308
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 308
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513