Error: [-E and CE, LG Washer Fault Codes
Failure Code: [-E and CE, LG Washer Fault Codes. Heating error and Over current error
Subject: LG Appliances - Sub Subject: LG WasherDate: 4/13/2019 Status: SOLVED
7 answered / 6 voted,
637 viewed.
technician - Saturday, April 13, 2019 706[-E: Heating error. Cause: the thermistor is out of order.
CE: Over current error. Cause: Main PWB assembly is out of order, Winding in the stator assembly is short circuited.
The best ReplyANSWERS Write an Answer
❝Error: [-E and CE, LG Washer Fault Codes❞ answers. technician asked first. Total 7 replies.
What does CE mean on LG washer?
LG Appliances / LG Washer The CE error code indicates that there has been an over-current in the electrical circuit of the motor. It is caused by a short circuit, loose connection, ground fault or power surge. To fix this: Unplug the washer for 10 seconds.
0
0What does [-E mean on LG washer?
LG Appliances / LG Washer [-E: Heating error. Cause: the thermistor is out of order.
0 0🚕 Green Bay, WI?
.. Interesting 🥇🏽 👋 0 0wait for me Gresham, OR?
0 0 0 0 0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 560
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3726
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 676
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 558
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 388
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 435
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 371
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 585
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 352
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 354
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513