LG Washing and Washer Dryers Machine Fault Codes
Learn Error codes or Er messages that may appear on the display / screen of LG washing machines / washer dryers.
Subject: Washing and Washer Machines - Sub Subject: Fault CodesDate: 3/22/2019 Status: SOLVED
6 answered / 1 voted,
307 viewed.
technician - Tuesday, March 26, 2019 385Indicates a problem with water supply. Possible causes for this include:
-Water supply taps are not completely open
-A kink in the inlet hose(s)
-The filter of the hose(s) are clogged.
ERROR DE: Draining Error
If the water has not drained within 5 minutes, DE (Draining Error) will appear. The drain hose being kinked or clogged, or the drain filter being clogged could cause this.
ERROR UE: Unbalanced Error
This means that the load is too small, over loaded, or out of balance - the appliance has an imbalance detection correction system. It will attempt to correct the imbalance itself, but it fails, it will display the UE error. You can adjust the size of load or rearrange the load to correct the error.
The best ReplyANSWERS Write an Answer
❝LG Washing and Washer Dryers Machine Fault Codes❞ answers. technician asked first. Total 6 replies.
This error with appear if you try to press start while the washing machine door is still open.
ERROR tE, TE1, TE2, TE3, TE4:
There is an issue with thermistor. Please unplug the machine and contact LG Services.
ERROR FE: Overflow Error
Water is overfilling to a fault with the water valve. Please close the water tap, unplug the power and contact LG Services.
ERROR PE: Pressure Sensor Switch Error
The water level sensor has malfunctioned. Please close the water tap, unplug the power and contact LG Services.
ERROR CE: Current Error
There is an overload in the motor. Please close the water tap, unplug the power and contact LG Services.
1
0There has been an error with the motor. Please close the water tap, unplug from power and contact LG Services.
ERROR PF: Power Failure Error
The washer experienced a power failure. Try restarting the cycle.
ERROR dHE: Dry Heater Error
Try powering down your unit unplugging, allowing your unit to sit for 10 seconds before plugging in and powering up again. If the error code persists, contact LG Services.
ERROR AE: Suspected Leak Error
The error in indicative that there is a leak somewhere in the washer, and it has triggered flood protection device found at the bottom of the washer.
1 0This indicates an issue with the heating element. Please unplug the unit and contact LG Services.
1 0ERROR LE: Lock Error
There has been an error with the motor. Please close the water tap, unplug from power.
can I repair it without calling the service?
1 0 0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 624
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3868
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 702
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 588
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 413
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 458
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 394
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 618
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 383
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 380
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513