F/10 Failure Code WHIRLPOOL Duet Duet HT
Error F/10 Failure Code WHIRLPOOL Duet Duet HT. Motor Control Unit (MCU) Heat Sink Thermal Trip
Subject: WHIRLPOOL - Sub Subject: Duet & Duet HTDate: 4/11/2019 Status: SOLVED
5 answered / 10 voted,
307 viewed.
technician - Thursday, April 11, 2019 378Condition: Motor Control Unit (MCU) Heat Sink Thermal Trip
If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an F/10 will be displayed.
Check/Repair:
- Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation.
- Check Wire Harness connectors to the MCU, and Central - - Control Unit (CCU)
- Check the Drive system for any worn or failed components
- Check MCU
Check Motor
The best ReplyANSWERS Write an Answer
❝F/10 Failure Code WHIRLPOOL Duet Duet HT❞ answers. technician asked first. Total 5 replies.
F10 Failure Code WHIRLPOOL Duet Duet HT
WHIRLPOOL / Duet & Duet HT If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an F10 will be displayed.
0
0 0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 552
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3721
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 674
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 556
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 385
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 431
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 367
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 582
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 348
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 346
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513