WHIRLPOOL Duet Duet HT F/11 Failure Code
Error F/11 WHIRLPOOL Duet Duet HT Failure Code. Serial Communication Error
Subject: WHIRLPOOL - Sub Subject: Duet & Duet HTDate: 4/11/2019 Status: SOLVED
5 answered / 5 voted,
350 viewed.
technician - Thursday, April 11, 2019 472Condition:Serial Communication Error
Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.
Check/Repair:
- Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)
- Check the Drive system for any worn or failed components
- Check MCU
- Check CCU
- Check Motor
- Check Wire Harness
The best ReplyANSWERS Write an Answer
❝WHIRLPOOL Duet Duet HT F/11 Failure Code❞ answers. technician asked first. Total 5 replies.
How do I fix the f11 code on my Whirlpool Duet washer?
WHIRLPOOL / Duet & Duet HT Resolution: Error code F11 = Serial Communication Error. Error codes can be caused by a Power Surge or other electrical anomaly,attempt to return the washer to operation by following the Hard Reset procedure below. In some cases the control can be non-functioning or may not accept activation from the control panel.
0
0 0 0 0 0 0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 512
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3633
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 636
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 515
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 349
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 393
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 322
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 536
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 304
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 306
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513