How to change a whirlpool dishwasher filter? [Whirlpool]

How to change a whirlpool dishwasher filter?

How to Change a Whirlpool Dishwasher Filter Open the Whirlpool dishwasher door. Lower the door as far as it will go. Move the rotating arm so the filtration system can be accessed. Rotate the upper filter assembly 1/4-turn counterclockwise to unlock it.

Subject: Whirlpool - Sub Subject: Dishwasher
Date: 6/26/2019 Status: ACTIVE

Viewed

7 times.

ANSWERS Write an Answer

❝How to change a whirlpool dishwasher filter?❞ answers. Askme asked first. Total 1 replies.

Askme - 6/26/2019 10:58:24 AM

Open the Whirlpool dishwasher door. Lower the door as far as it will go.
Move the rotating arm so the filtration system can be accessed.
Rotate the upper filter assembly 1/4-turn counterclockwise to unlock it.
Lift the upper filter assembly straight up to remove it.

Did you find this helpful? like icon

Similar Questions

How do I fix H2O error code on GE dishwasher?

How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.

GE / Dishwasher Answers: 1 100

How do I fix 999 error code on GE dishwasher?

How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.

GE / Dishwasher Answers: 1 19

How do I fix Leak Detected error code on GE dishwasher?

How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.

GE / Dishwasher Answers: 1 22

How do I fix C8 error code on GE dishwasher?

How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.

GE / Dishwasher Answers: 1 23

How do I fix C7 error code on GE dishwasher?

How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.

GE / Dishwasher Answers: 1 10

How do I fix C6 error code on GE dishwasher?

How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem

GE / Dishwasher Answers: 1 12

How do I fix C5 error code on GE dishwasher?

How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t

GE / Dishwasher Answers: 1 9

How do I fix C4 error code on GE dishwasher?

How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l

GE / Dishwasher Answers: 1 14

Tepte