What causes Whirlpool washer to show fault codes E01 and F03?
What causes Whirlpool washer to show fault codes E01 and F03; Pull the machine out from the wall; Take the screws out along the rear lip of the machine. Push the top back and lift it off. Once off in the rear right corner you will see the pressure switch, it’s the part with the plastic tube attached
Subject: Whirlpool - Sub Subject: All-In-One Washer DryerDate: 4/11/2020 Status: SOLVED
3 answered / 3 voted,
745 viewed.
Askme - Saturday, April 11, 2020 838F3E1 - Error Code - All-In-One Washer Dryer
Whirlpool / All-In-One Washer Dryer Pull the machine out from the wall; Take the screws out along the rear lip of the machine. Push the top back and lift it off. Once off in the rear right corner you will see the pressure switch, it’s the part with the plastic tube attached.
F3E1 - Error Code - All-In-One Washer Dryer
Water Pressure Issue
The F3E1 Error Code indicates that there may be aproblem with the Water Pressure sensor. Verify that your water supply has the adequate amount of pressure going to the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in. You may need to run a drain only cycle if there is still water in the Washer/Dryer. If unsuccessful, call for service.
The best ReplyANSWERS Write an Answer
❝What causes Whirlpool washer to show fault codes E01 and F03?❞ answers. Askme asked first. Total 3 replies.
wait for me Brockton, MA?
.. 🌜 ✈ 🌕 🥈 ⛅ ⌚ ⚡✋
0
0 0 0Similar Questions
My Breville microwave not heat anything
Hi i have a Breville microwave, all the functions are working as normal but my food is not getting hot at all, I dont understand microwaves but would love to be able fix it myself, can you help me with the diagnosis please?
Breville / Microwave Answers: 7 513
How do I fix H2O error code on GE dishwasher?
How do I fix H2O error code on GE dishwasher: Indicates a low water situation. If H2O only appears during 1-Hour Wash, schedule service. Feel free to run any other cycle until that update is done.
GE / Dishwasher Answers: 8 3638
How do I fix 999 error code on GE dishwasher?
How do I fix 999 error code on GE dishwasher; Possible leak detected on models with “Floor Protect with Alert” feature. All others: The unit’s control needs to be reset.
GE / Dishwasher Answers: 7 638
How do I fix Leak Detected error code on GE dishwasher?
How do I fix Leak Detected error code on GE dishwasher; Possible leak is detected. The cycle will be cancelled on models with leak detection. If LEAK DETECTED is displayed, contact service.
GE / Dishwasher Answers: 7 516
How do I fix C8 error code on GE dishwasher?
How do I fix C8 error code on GE dishwasher; This display indicates that the detergent cup is blocked from opening fully. Remove obstruction (i.e. silverware, pan). Relatch door and wait 30 seconds for cup to open.
GE / Dishwasher Answers: 7 351
How do I fix C7 error code on GE dishwasher?
How do I fix C7 error code on GE dishwasher; The dishwasher’s water temperature sensor circuit has become inoperative. Disconnect the power at the circuit breaker for about 30 seconds and then reset the dishwasher.
GE / Dishwasher Answers: 8 395
How do I fix C6 error code on GE dishwasher?
How do I fix C6 error code on GE dishwasher; Water temperature is too low. Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater tem
GE / Dishwasher Answers: 7 325
How do I fix C5 error code on GE dishwasher?
How do I fix C5 error code on GE dishwasher; The pump out time is too short. Make sure that the water supply is turned on. Try the same cycle again. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front left corner of the floor of t
GE / Dishwasher Answers: 7 537
How do I fix C4 error code on GE dishwasher?
How do I fix C4 error code on GE dishwasher; Machine filled twice after a power failure. Float switch stuck or failed. Clogged drain or sump. Touch start and then cancel/reset. Tap on the float cover to unstick the float. This is the plastic cover that looks like an upside down cup in the front l
GE / Dishwasher Answers: 4 310
How do I fix C3 error code on GE dishwasher?
How do I fix C3 error code on GE dishwasher; The dishwasher will not drain. Disconnect power, reset the dishwasher.
GE / Dishwasher Answers: 5 308
Similar Articles
Microsoft OLE DB Provider for ODBC Drivers
error '80004005'[MySQL][ODBC 8.0(w) Driver][mysqld-8.0.44]Can't find FULLTEXT index matching the column list
/soru.asp, line 513